cabletest/docs/panels/rvt70/riverdi-rvt70hstnwc00-b-datasheet.md

# Riverdi RVT70HSTNWC00-B datasheet — transcription

Full visual transcription (tables intact) of the Riverdi public datasheet
`DS_RVT70HSTNWC00-B Rev.1.2` ("IPS RGB 7.0" LCD TFT DATASHEET", TFT Module Specification), all
19 pages. Source PDF alongside as
[riverdi-rvt70hstnwc00-b-datasheet.pdf](riverdi-rvt70hstnwc00-b-datasheet.pdf).

This is the **TFT panel** — parallel RGB interface, 3.3 V, driven directly by the host's pixel
clock. It is the panel inside the HDMI module
[RVT70HSHNWC00-B](riverdi-rvt70hshnwc00-b-datasheet.md), whose section 11 names it (as
"RVT70HSTNWC00-B") and defers all display detail here. It is therefore the only source for the
panel's timing numbers: section 13.3 carries the DE-mode and HV-mode tables the module
datasheet omits.

Note what this timing does and does not govern. On the HDMI module the RTD2660H scaler owns
this RGB interface and retimes whatever arrives over HDMI onto it, so these figures are the
panel's own limits, not the timing a HDMI source must send.

Transcription notes:

- Each page's content begins with an HTML comment page marker `<!-- p.N -->` (N = the printed
  datasheet page number) for cross-reference and continuity.
- Every specification, pinout and criteria table is reproduced as a Markdown table. Cells merged
  across rows in the original are repeated per row.
- Graphical figures, waveform diagrams and the mechanical drawing are **not** pixel-reproduced;
  they are given a short prose description prefixed `*Figure (described):*`, with all dimension
  and label callouts transcribed.
- Pure transcription: no cabletest commentary is interleaved, and typographic errors in the
  original (e.g. "OPATICAL BONDING", "Add" inch" unit") are reproduced as printed.

---

<!-- p.1 -->

*(Cover page. Left edge carries the vertical banner text "TFT MODULE SPECIFICATION". Riverdi
logo centred at the top.)*

# RVT70HSTNWC00-B

## IPS RGB 7.0" LCD TFT DATASHEET

Rev.1.2

2021-07-29

| ITEM | CONTENTS | UNIT |
| --- | --- | --- |
| LCD Type | TFT/Transmissive/Normally black/IPS | / |
| Size | 7.0 | Inch |
| Viewing Direction | Free | / |
| Outside Dimensions (W x H x D) | 179.96 x 119.00 x 7.58 | mm |
| Active Area (W x H) | 154.21 x 85.92 | mm |
| Pixel Pitch (W x H) | 0.1506 x 0.1432 | mm |
| Resolution | 1024 (RGB) x 600 | / |
| Brightness | 850 | cd/m² |
| LCD Interface Type | RGB | / |
| Color Depth | 16.7 M | / |
| Pixel Arrangement | RGB Vertical Stripe | / |
| With/Without Touch | With Projected Capacitive Touch Panel | / |
| CTP Driver | ILI2132A | / |
| Touch Interface Type | USB /I2C/ Optional UART | / |
| Bonding Technology | Optical Bonding | / |
| Weight | 214 | g |

**Note 1:** RoHS3 compliant

**Note 2:** LCM weight tolerance: ± 5%.

---

<!-- p.2 -->

## 1. REVISION RECORD

| REV NO. | REV DATE | CONTENTS | REMARKS |
| --- | --- | --- | --- |
| 1.0 | 2020-08-15 | Initial Release | |
| 1.1 | 2021-04-20 | Add" inch" unit on drawing | |
| 1.2 | 2021-07-29 | Updating new template | |

---

<!-- p.3 -->

## 2. CONTENTS

| Section | Page |
| --- | --- |
| 1. REVISION RECORD | 2 |
| 2. CONTENTS | 3 |
| 3. MODULE CLASSIFICATION INFORMATION | 4 |
| 4. uxTouch ASSEMBLY | 5 |
| 5. MODULE DRAWING | 6 |
| 6. ABSOLUTE MAXIMUM RATINGS | 7 |
| 7. ELECTRICAL CHARACTERISTICS | 7 |
| 8. BACKLIGHT ELECTRICAL CHARACTERISTICS | 7 |
| 9. POWER CONSUMPTION | 8 |
| 10. ELECTRO-OPTICAL CHARACTERISTICS | 8 |
| 11. BLOCK DIAGRAM | 10 |
| 12. INTERFACES DESCRIPTION | 10 |
| 12.1 TFT assignment | 10 |
| 12.2 Touch panel assignment | 12 |
| 12.3 CON1 assignment | 13 |
| 13. TIMING CHARACTERISTICS | 13 |
| 13.1 Horizontal input timing | 13 |
| 13.2 Vertical input timing | 13 |
| 13.3 Parallel RGB timing characteristic | 14 |
| 13.3.1 DE MODE | 14 |
| 13.3.2 HV MODE – Horizontal input timing | 14 |
| 13.3.3 HV MODE – Vertical input timing | 14 |
| 13.3.4 Power On/Off sequence | 15 |
| 14. CAPACITIVE TOUCH SCREEN PANEL SPECIFICATIONS | 15 |
| 14.1 Mechanical characteristics | 15 |
| 14.2 Electrical characteristics | 15 |
| 15. INSPECTION | 16 |
| 15.1 Inspection condition | 16 |
| 15.2 Inspection standard | 17 |
| 16. RELIABILITY TEST | 18 |
| 17. LEGAL INFORMATION | 19 |

---

<!-- p.4 -->

## 3. MODULE CLASSIFICATION INFORMATION

| RV | T | 70 | H | S | T | N | W | C | 00 | B |
| --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- |
| 1. | 2. | 3. | 4. | 5. | 6. | 7. | 8. | 9. | 10. | 11. |

| NO. | PARAMETER | SYMBOL |
| --- | --- | --- |
| 1. | BRAND | RV – Riverdi |
| 2. | PRODUCT TYPE | T – TFT Standard |
| 3. | DISPLAY SIZE | 70 – 7.0" |
| 4. | MODEL SERIAL NO. | H – High Brightness, IPS |
| 5. | RESOLUTION | S – 1024 x 600 px |
| 6. | INTERFACE | T – TFT LCD, RGB |
| 7. | FRAME | N – Without Mounting Metal Frame |
| 8. | BACKLIGHT TYPE | W – LED White |
| 9. | TOUCH PANEL | C – With Capacitive Touch Panel |
| 10. | VERSION | 00 – (00-99) |
| 11. | BONDING TECHNOLOGY | B – Optical Bonding |

---

<!-- p.5 -->

## 4. uxTouch ASSEMBLY

uxTouch are LCD TFT displays with specially designed projected capacitive touch panels.
uxTouch display can be mounted without any additional holes in the housing. Our standard
uxTouch displays include double-sided adhesive tape (DST) to stick TFT easily to the housing.

uxTouch models with double-side adhesive tape can be mounted by fastening the glass to the
housing.

*Figure 1. General view of the module*

*Figure (described):* two 3-D renderings of the module in a blue housing — front view showing
the grey active area behind the cover glass, and rear three-quarter view showing the green
panel PCB and flex tail recessed into the housing.

---

<!-- p.6 -->

## 5. MODULE DRAWING

*Figure (described):* ISO A3 landscape mechanical drawing, scale 1:1.66, dimensions in mm with
inches in square brackets. Title block: PN RVT70HSTNWC00-B; DRAWN M.Natywa 2021.04.19;
CHECKED Carol 2021.04.20; first-angle projection; P. 1 of 1.

Drawing revision table:

| Revision: | Changes: | Date: |
| --- | --- | --- |
| 1.0 | Initial Case | 2020.08.07 |
| 1.1 | Dimension Overhaul | 2021.04.19 |

Front-view horizontal callouts (top group, outermost first):

| Dimension | Inches | Meaning |
| --- | --- | --- |
| 179.96 | [7.085] | CG O.D. |
| 164.90 | [6.492] | TFT O.D. |
| 163.66 | [6.443] | SENSOR O.D. |
| 156.68 | [6.169] | SENSOR A.A. |
| 155.01 | [6.103] | CG V.A. |
| 154.21 | [6.071] | TFT A.A. |
| 89.98 | [3.543] | — (horizontal centre offset) |

Front-view horizontal callouts (right-hand group):

| Dimension | Inches |
| --- | --- |
| 5.90 | [0.232] |
| 6.74 | [0.265] |
| 11.64 | [0.458] |
| 12.48 | [0.491] |
| 12.97 | [0.511] |

Front-view vertical callouts (left group, outermost first):

| Dimension | Inches | Meaning |
| --- | --- | --- |
| 119.00 | [4.685] | CG O.D. |
| 100.00 | [3.937] | TFT O.D. |
| 98.55 | [3.880] | SENSOR O.D. |
| 88.52 | [3.485] | SENSOR A.A. |
| 86.72 | [3.414] | CG V.A. |
| 85.92 | [3.383] | TFT A.A. |
| 59.50 | [2.343] | — (vertical centre offset) |

Front-view vertical callouts (upper group):

| Dimension | Inches |
| --- | --- |
| 11.58 | [0.456] |
| 12.20 | [0.480] |
| 15.24 | [0.600] |
| 16.14 | [0.635] |
| 16.54 | [0.651] |

Further front-view callouts: 72.73 [2.865] (left, to the flex tail); 34.00 [1.339] and
41.75 [1.644] (right); 57.05 [2.246]; 5.00 [0.197]; 23.48 [0.924]; 50.98 [2.007];
35.00 [1.378]; 74.45 [2.931]; 77.36 [3.046]; 102.86 [4.050]; 107.74 [4.242]; 121.49 [4.783].
Corner radius `4*R5.00 [R0.197]`. Front face annotated `BLACK MASK PRINTING RAL9005`.

Side-view (thickness) callouts:

| Dimension | Inches | Meaning |
| --- | --- | --- |
| 7.58 | [0.298] | O.D. |
| 2.03 | [0.060] | CG+SCA+SENSOR+OCA |
| 1.28 | [0.050] | CG+DST |
| 1.10 | [0.043] | CG |

Flex-tail stack callouts: COMPONENT AREA — STIFFENER; 1.70 [0.067](MAX); 3.50 [0.138](MAX);
STIFFENER — CONTACT SIDE; CONTACT SIDE — STIFFENER; 0.30 [0.012] (×2).

Rear view annotated `3M9495LE T=0.175mm[0.007]` and `BLACK TAPE T=0.05mm[0.002]`, with
5.50 [0.217] on the touch flex.

DETAIL A, SCALE 2:1 — the 50-pin TFT flex tail: pins 1 to 50, 3.80 [0.150], 25.50 [1.004],
`2*0.50 [0.020]`, `W:0.35 [0.014]`, `P:(50-1)*0.5=24.50 [0.985]`.

DETAIL B, SCALE 4:1 — connector CN1, `JST SM04B-SRSS-TB`, pins 1 to 4,
`MATCHING CABLE CONNECTOR: JST SHR-04V-S-B`.

DETAIL C, SCALE 4:1 — cover glass edge chamfers, both `0.20 [0.008]*45°`.

DETAIL D, SCALE 2:1 — the 10-pin touch flex tail: pins 1 to 10, 3.50 [0.138], 5.50 [0.217],
`2*0.50 [0.020]`, `W:0.30 [0.012]`, `P:(10-1)*0.50=4.50 [0.177]`.

LED Diagram Circuit: three parallel strings of nine series LEDs between LEDA and LEDK.

TFT NOTES:

1. LCD TYPE: TRANSMISSIVE, NORMALLY BLACK,IPS
2. RESOLUTION: 1024x600
3. VIEWING ANGLE: FREE
4. LCD DRIVER:EK79001HK+EK73215BCGA
5. INTERFACE:RGB
6. OPERATING VOLTAGE: 3.3V
7. BACKLIGHT: 27PCS LED, V<sub>F</sub>=9.6V, I<sub>F</sub>=270mA

TP NOTES:

1. TP STRUCTURE: G+G
2. CG THICKNESS: 1.10 mm
3. DRIVER IC: ILI2132A
4. INTERFACE: USB /I2C/OPTIONAL UART
5. OPERATING VOLTAGE: 3.3V(CTP I2C); 5.0V(CTP USB)

GENERAL NOTES:

1. MODULE SURFACE LUMINANCE: 850 cd/m^2
2. OPATICAL BONDING
3. OPERATING TEMPERATURE: -20°C ~ 70°C
4. STORAGE TEMPERATURE: -30°C ~ 80°C
5. WITHOUT INDIVIDUAL TOLERANCE: ±0.3mm
6. RoHS3 COMPLIANT

---

<!-- p.7 -->

## 6. ABSOLUTE MAXIMUM RATINGS

| PARAMETER | SYMBOL | MIN | MAX | UNIT |
| --- | --- | --- | --- | --- |
| Power for Circuit Driving | VDD | -0.3 | 3.96 | V |
| Power for Circuit Driving | AVDD | -0.5 | 14.85 | V |
| Power for Circuit Driving | VGH | -0.3 | 40 | V |
| Power for Circuit Driving | VGL | -20.0 | 0.3 | V |
| Operating Temperature | T<sub>OP</sub> | -20 | 70 | °C |
| Storage Temperature | T<sub>ST</sub> | -30 | 80 | °C |
| Operating Humidity (@ 25 ± 5°C) | RH | 10% | - | RH |
| Storage Humidity (@ 25 ± 5°C) | RH | 10% | - | RH |

**Note.** The following are maximum values. If exceeded, it may cause operation or damage to
the unit.

## 7. ELECTRICAL CHARACTERISTICS

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNIT | NOTE |
| --- | --- | --- | --- | --- | --- | --- |
| Supply Voltage for Module | DVDD | 3.0 | 3.3 | 3.6 | V | |
| Supply Voltage for Module | VGH | 17 | 18 | 19 | V | |
| Supply Voltage for Module | VGL | -6.6 | -6.0 | -5.4 | V | |
| Supply Voltage for Module | AVDD | 9.4 | 9.6 | 9.8 | V | |
| Supply Voltage for Module | VCOM | 3.6 | 3.8 | 4.0 | V | |
| Current of Power Supply | IDD | - | 30 | 45 | mA | DVDD = 3.3V |
| Current of Power Supply | IADD | - | 35 | 45 | mA | AVDD = 9.6V |
| Current of Power Supply | IGH | - | 0.5 | 1 | uA | VGH = 18V |
| Current of Power Supply | IGL | - | 0.5 | 1 | mA | VGL= -6V |
| Input Voltage ' H ' level | V<sub>IH</sub> | 0.7DVDD | - | DVDD | V | Note 1 |
| Input Voltage ' L ' level | V<sub>IL</sub> | 0 | - | 0.3VDD | V | Note 1 |

**Note 1.** STHL, STHR, OEH, L/R, CPH1÷CPH3, STVD, STVU, OEV, CKV, U/D.

## 8. BACKLIGHT ELECTRICAL CHARACTERISTICS

| PARAMETER | SYMBOL | MIN | TYP | MAX | UNIT | NOTE |
| --- | --- | --- | --- | --- | --- | --- |
| Backlight Driving Voltage | V<sub>F</sub> | 9.0 | 9.6 | 10.2 | V | |
| Backlight Driving Current | I<sub>F</sub> | - | 270 | - | mA | |
| Backlight Power Consumption | W<sub>BL</sub> | - | 2592 | - | mW | |
| LED Lifetime | - | - | 50,000 | - | hours | Note 1 |

**Note 1.** If LED is driven by high current, the lifetime of LED will be reduced. Operating
life means brightness goes down to 50% initial brightness. Typical operating lifetime is
estimated data.

---

<!-- p.8 -->

## 9. POWER CONSUMPTION

| PARAMETER | SYMBOL | CONDITION | MIN | TYP | MAX | UNIT | NOTE |
| --- | --- | --- | --- | --- | --- | --- | --- |
| Gate on Power Current | IVGH | VGH=18V | - | 0.5 | 1 | mA | Note 1 |
| Gate off Power Current | IVGL | VGL=6V | - | 0.5 | 1 | mA | Note 1 |
| Digital Power Current | IDVDD | DVDD=3.3V | - | 30 | 45 | mA | Note 1 |
| Analog Power Current | IAVDD | AVDD=9.6 V | - | 35 | 45 | mA | Note 1 |
| Total Power Consumption | PC | | - | 447 | 604 | mW | Note 1 |

**Note.** Typ. Specification: Gray-level test pattern; Max Specification: Black test pattern

*Figure (described):* two swatches illustrating the two test patterns — a horizontal black-to-
white gradient labelled "256 gray patten", and a solid black rectangle labelled "black
pattern".

## 10. ELECTRO-OPTICAL CHARACTERISTICS

| ITEM | SYMBOL | CONDITION | MIN | TYP | MAX | UNIT | RMK | NOTE |
| --- | --- | --- | --- | --- | --- | --- | --- | --- |
| Response Time | Tr+Tf | θ=0°<br>ø=0°<br>Ta=25 °C | - | 35 | - | ms | FIG 2. | 4 |
| Contrast Ratio | Cr | θ=0°<br>ø=0°<br>Ta=25 °C | - | 800 | - | --- | FIG 3 | 1 |
| Luminance Uniformity | δ WHITE | θ=0°<br>ø=0°<br>Ta=25 °C | - | 75 | - | % | FIG 3. | 3 |
| Surface Luminance | Lv | θ=0°<br>ø=0°<br>Ta=25 °C | - | 850 | - | cd/m² | FIG 3. | 2 |
| Viewing Angle Range | θ | ø = 90° | - | 85 | - | deg | FIG 4. | 6 |
| Viewing Angle Range | θ | ø = 270° | - | 85 | - | deg | FIG 4. | 6 |
| Viewing Angle Range | θ | ø = 0° | - | 85 | - | deg | FIG 4. | 6 |
| Viewing Angle Range | θ | ø = 180° | - | 85 | - | deg | FIG 4. | 6 |
| CIE (x, y) Chromaticity | Rx | θ=0°<br>ø=0°<br>Ta=25 °C | 0.578 | 0.618 | 0.658 | - | FIG 3. | 5 |
| CIE (x, y) Chromaticity | Ry | θ=0°<br>ø=0°<br>Ta=25 °C | 0.489 | 0.329 | 0.369 | - | FIG 3. | 5 |
| CIE (x, y) Chromaticity | Gx | θ=0°<br>ø=0°<br>Ta=25 °C | 0.376 | 0.416 | 0.456 | - | FIG 3. | 5 |
| CIE (x, y) Chromaticity | Gy | θ=0°<br>ø=0°<br>Ta=25 °C | 0.493 | 0.533 | 0.573 | - | FIG 3. | 5 |
| CIE (x, y) Chromaticity | Bx | θ=0°<br>ø=0°<br>Ta=25 °C | 0.071 | 0.111 | 0.151 | - | FIG 3. | 5 |
| CIE (x, y) Chromaticity | By | θ=0°<br>ø=0°<br>Ta=25 °C | 0.108 | 0.148 | 0.188 | - | FIG 3. | 5 |
| CIE (x, y) Chromaticity | Wx | θ=0°<br>ø=0°<br>Ta=25 °C | 0.270 | 0.310 | 0.350 | - | FIG 3. | 5 |
| CIE (x, y) Chromaticity | Wy | θ=0°<br>ø=0°<br>Ta=25 °C | 0.290 | 0.330 | 0.370 | - | FIG 3. | 5 |

**Note 1.** Contrast Ratio (CR) is defined mathematically as below, for more information see
Figure 3.

> Contrast Ratio = Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5) ÷
> Average Surface Luminance with all black pixels (P1, P2, P3, P4, P5)

**Note 2.** Surface luminance is the LCD surface from the surface with all pixels displaying
white. For more information see Figure 3.

---

<!-- p.9 -->

> Lv = Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)

**Note 3.** The uniformity in surface luminance δ WHITE is determined by measuring luminance at
each test position 1 through 5, and then dividing the minimum luminance of 5 points luminance
by maximum luminance of 5 points luminance. For more information see Figure 3.

> δ WHITE = Minimum Surface Luminance with all white pixels (P1, P2, P3, P4, P5) ÷
> Maximum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)

**Note 4.** Response time is the time required for the display to transition from white to
black (Rise Time, Tr) and from black to white (Decay Time, Tf). For additional information see
Figure 2. The test equipment is Autronic-Melchers's ConoScope series.

**Note 5.** CIE (x, y) chromaticity, the x, y value is determined by measuring luminance at each
test position 1 through 5, and then make average value.

**Note 6.** Viewing angle is the angle at which the contrast ratio is greater than 2. For TFT
module the contrast ratio is greater than 10. The angles are determined for the horizontal or x
axis and the vertical or y axis with respect to the z axis which is normal to LCD surface. For
more information see Figure 4.

**Note 7.** For viewing angle and response time testing, the testing data is based on
Autronic-Melchers's ConoScope series. Instruments for Contrast Ratio, Surface Luminance,
Luminance Uniformity, CIE the test data is based on TOPCON's BM-5 photo detector.

*Figure 2. The definition of response time*

*Figure (described):* optical response versus time trace. The vertical axis is marked 0%, 10%,
90% and 100%. The trace starts at 100% ("white"), falls through the 90%→10% band in the
interval marked Tr, holds at 0% ("black"), then rises back through 10%→90% in the interval
marked Tf, returning to 100% ("white").

*Figure 3. Measuring method for Contrast ratio, surface luminance, Luminance uniformity,
CIE (x, y) chromaticity*

*Figure (described):* plan view of the active area with five measurement points — P1 top left,
P2 top right, P3 bottom right, P4 bottom left and P5 at the centre. Horizontal extent labelled
H, vertical extent labelled V, corner insets labelled A (horizontal) and B (vertical).
Accompanying legend:

- A: 5mm
- B: 5mm
- H, V: Active Area
- Light spot size φ=5mm, 500mm distance from the LCD surface to detector lens.
- Measurement instrument is TOPCON'S luminance meter BM-5

---

<!-- p.10 -->

*Figure 4. The definition of viewing angle*

*Figure (described):* isometric sketch of the LCD plane with the z axis normal to the surface at
θ=0, the polar angle θ swept from that normal and the azimuth Φ swept in the plane. Azimuth
references marked around the panel: Up Φ=90 (12:00), Left Φ=180 (9:00), Right Φ=0 (3:00),
Down Φ=270 (6:00).

## 11. BLOCK DIAGRAM

*Figure (described):* block diagram. A signal-input block listing `VGH, VGL, AVDD, LV0N/P,
LV1N/P, LV2N/P, LV3N/P, LVCLKN/P, RESET, STBYB, VCOM, VDD, GND, VLED+, VLED-` feeds three
blocks to its left: "Gate driver IC", "Source driver IC +TCON" and "Back light". The gate and
source driver blocks in turn feed the "LCD Panel 7.0 inch 1024×600" block; the backlight block
feeds it as well.

## 12. INTERFACES DESCRIPTION

### 12.1 TFT assignment

| PIN NO. | SYMBOL | I/O | DESCRIPTION | NOTES |
| --- | --- | --- | --- | --- |
| 1 | VLED+ | P | Power for LED Backlight (Anode) | |
| 2 | VLED+ | P | Power for LED Backlight (Anode) | |
| 3 | VLED- | P | Power for LED Backlight (Cathode) | |
| 4 | VLED- | P | Power for LED Backlight (Cathode) | |
| 5 | GND | P | Ground | |
| 6 | VCOM | I | Common Voltage | |

---

<!-- p.11 -->

| PIN NO. | SYMBOL | I/O | DESCRIPTION | NOTES |
| --- | --- | --- | --- | --- |
| 7 | DVDD | P | Power for Digital Circuit | |
| 8 | MODE | I | DE/SYNC mode select | Note 1 |
| 9 | DE | I | Data Input Enable | |
| 10 | VS | I | Vertical Sync Input | |
| 11 | HS | I | Horizontal Sync Input | |
| 12 | B7 | I | Blue Data (MSB) | |
| 13 | B6 | I | Blue Data | |
| 14 | B5 | I | Blue Data | |
| 15 | B4 | I | Blue Data | |
| 16 | B3 | I | Blue Data | |
| 17 | B2 | I | Blue Data | |
| 18 | B1 | I | Blue Data | Note 2 |
| 19 | B0 | I | Blue Data (LSB) | Note 2 |
| 20 | G7 | I | Green Data (MSB) | |
| 21 | G6 | I | Green Data | |
| 22 | G5 | I | Green Data | |
| 23 | G4 | I | Green Data | |
| 24 | G3 | I | Green Data | |
| 25 | G2 | I | Green Data | |
| 26 | G1 | I | Green Data | Note 2 |
| 27 | G0 | I | Green Data (LSB) | Note 2 |
| 28 | R7 | I | Red Data (MSB) | |
| 29 | R6 | I | Red Data | |
| 30 | R5 | I | Red Data | |
| 31 | R4 | I | Red Data | |
| 32 | R3 | I | Red Data | |
| 33 | R2 | I | Red Data | |
| 34 | R1 | I | Red Data | Note 2 |
| 35 | R0 | I | Red Data (LSB) | Note 2 |
| 36 | GND | P | Ground | |
| 37 | DCLK | P | Sample Clock | |
| 38 | GND | P | Ground | |
| 39 | L/R | I | Left/Right Selection | Note 4,5 |
| 40 | U/D | I | Up/Down Selection | Note 4,5 |
| 41 | VGH | P | Gate ON Voltage | |
| 42 | VGL | P | Gate OFF Voltage | |
| 43 | AVDD | P | Power for Analog Circuit | |
| 44 | RESET | I | Global Reset Pin | Note 6 |
| 45 | NC | - | No Connection | |
| 46 | VCOM | I | Common Voltage | |
| 47 | DITHUB | I | Dithering Function | Note 7 |
| 48 | GND | I | Ground | |
| 49 | NC | - | No Connection | |
| 50 | NC | - | No Connection | |

I: input, O: output, P: Power

**Note 1.** DE/SYNC mode select. Normally pull high.

---

<!-- p.12 -->

H:DE Mode. L: HS/VS mode.
When select DE mode, MODE="1", VS and HS must pull high.

**Note 2.** When input 18 bits RGB data, the two low bits of R, G and B data must be grounded.

**Note 3.** Data shall be latched at the falling edge of DCLK.

**Note 4.** Selection of scanning mode:

| SETTING OF SCAN CONTROL INPUT — U/D | SETTING OF SCAN CONTROL INPUT — L/R | SCANNING DIRECTION |
| --- | --- | --- |
| GND | DVDD | Up to down, left to right |
| DVDD | GND | Down to up, right to left |
| GND | GND | Up to down, right to left |
| DVDD | DVDD | Down to up, left to right |

**Note 5.** Definition of scanning direction, refer to the figure as below:

*Figure (described):* plan view of the module with its flex tail leaving the bottom edge. Arrows
label the four directions relative to that orientation: Up (arrow at the top edge pointing
down into the panel), Down (at the tail), Left (arrow entering the left edge pointing right)
and Right (arrow leaving the right edge).

**Note 6.** Global reset pin. Active low to enter reset state, suggest connecting with an RC
reset circuit for stability. Normally pull high.

**Note 7.** Dithering function enable control, normally pull high.
When DITHUB="1", Disable internal dithering function.
When DITHUB="0", Enable internal dithering function.

### 12.2 Touch panel assignment

| PIN NO. | SYMBOL | DESCRIPTION | NOTE |
| --- | --- | --- | --- |
| 1 | USB_GND | USB_ Ground | |
| 2 | USB_VDD | USB Power for CTP, 5.0V | |
| 3 | USB_D– | USB _Data Signal – | |
| 4 | USB_D+ | USB _Data Signal + | |
| 5 | I2C_GND | I2C _ Ground | Note 1 |
| 6 | I2C_VDD | I2C _Power for CTP, 3.3 V | Note 1 |
| 7 | I2C_RST | I2C _Reset Pin, Active low | Note 1 |
| 8 | I2C_SCL | I2C _Clock Input | Note 1 |
| 9 | I2C_INT | I2C _Interrupt Signal from CTP, Active low | Note 1 |
| 10 | I2C_SDA | I2C _Data Signal | Note 1 |

**Note 1.** External pull-up resistors are required.

---

<!-- p.13 -->

### 12.3 CON1 assignment

| PIN NO. | SYMBOL | DESCRIPTION |
| --- | --- | --- |
| 1 | USB_VDD | USB_Power for CTP, DC 5.0V |
| 2 | USB_D– | USB _Data Signal - |
| 3 | USB_D+ | USB _Data Signal + |
| 4 | USB_GND | USB_Ground |

## 13. TIMING CHARACTERISTICS

### 13.1 Horizontal input timing

*Figure (described):* horizontal timing waveform. Traces top to bottom: HSD (horizontal sync,
active-low pulse whose width is marked "H pulse width (thpw)"); CLK (free-running pixel clock);
then, under the heading "( HV mode)", three data buses D07~D00, D17~D10 and D27~D20 carrying
R, G and B samples respectively; then the same three buses again under the heading "( DE
mode)"; then DEN (data enable). Along the bottom, the line is divided into
`H back porch (thbp)`, `Active Area(thd)` and `H front porch (thfp)`, spanning
`Total Area(th)`.

### 13.2 Vertical input timing

*Figure (described):* vertical timing waveform. Traces top to bottom: VSD (vertical sync,
active-low pulse whose width is marked tvpw); HSD (horizontal sync burst, continuous through
the frame); DEN (data enable, gated on only during the active lines). Along the bottom the
frame is divided into `tvb`, `tvd` and `tvfp`, spanning `tv`.

---

<!-- p.14 -->

### 13.3 Parallel RGB timing characteristic

**Note:** DE/SYNC mode select. Normally pull high. H:DE Mode. L: HS/VS mode.
When select DE mode, MODE="1", VS and HS must pull high.

#### 13.3.1 DE MODE

| PARAMETER | SYMBOL | MIN. | TYP. | MAX. | UNIT |
| --- | --- | --- | --- | --- | --- |
| DCLK frequency (Frame rate 60Hz) | fclk | 40.8 | 51.2 | 67.2 | MHz |
| Horizontal display area | thd | | 1024 | | DCLK |
| HSYNC period time | th | 1114 | 1344 | 1400 | DCLK |
| HSYNC blanking | thb+thfp | 90 | 320 | 376 | DCLK |
| Vertical display area | tvd | | 600 | | H |
| VSYNC period time | tv | 610 | 635 | 800 | H |
| VSYNC blanking | tvb+tvfp | 10 | 85 | 200 | H |

#### 13.3.2 HV MODE – Horizontal input timing

| PARAMETER | SYMBOL | MIN. | TYP. | MAX. | UNIT |
| --- | --- | --- | --- | --- | --- |
| Horizontal display area | thd | | 1024 | | DCLK |
| DCLK frequency (frame rate 60Hz) | fclk | 44.9 | 51.2 | 63 | MHz |
| 1 Horizontal Line | th | 1200 | 1344 | 1400 | DCLK |
| HSYNC pulse width | thpw | 1 | - | 140 | DCLK |
| HSYNC back porch | thbp | 160 | 160 | 160 | DCLK |
| HSYNC front porch | thfp | 16 | 160 | 216 | DCLK |

#### 13.3.3 HV MODE – Vertical input timing

| PARAMETER | SYMBOL | MIN. | TYP. | MAX. | UNIT |
| --- | --- | --- | --- | --- | --- |
| Vertical display area | tvd | | 600 | | H |
| VSYNC period time | tv | 624 | 635 | 750 | H |
| VSYNC pulse width | tvpw | 1 | - | 20 | H |
| VSYNC back porch | tvb | 23 | 23 | 23 | H |
| VSYNC front porch | tVfp | 1 | 12 | 127 | H |

---

<!-- p.15 -->

#### 13.3.4 Power On/Off sequence

*Figure (described):* power sequencing waveform, split into a "Power on sequence" half and a
"Power off sequence" half. Traces top to bottom: VSD (continuous sync burst, with the frames
numbered across the sequence); VDD (rising first, annotated `≥20ms` and a small rise-time
callout); STB; AVDD; VGL; VGH; VCOMO (annotated `VCOMO=0V` on power-off); Source Output
(annotated `00 H`, then `Normal display`, then `00 H` and `LOW LEVEL`, with
`Source output =0V` at the end); BLEN (asserted after the panel is up, deasserted first on
power-down); GATE (annotated `OEV=H` at each end and `Normal` through the middle).

## 14. CAPACITIVE TOUCH SCREEN PANEL SPECIFICATIONS

### 14.1 Mechanical characteristics

| DESCRIPTION | SPECIFICATION | REMARK |
| --- | --- | --- |
| Touch Panel Size | 7.0 inch | uxTouch |
| Outline Dimension of CTP | 179.96 mm x 119.00 mm | uxTouch |
| Product Thickness | 2.03 mm | uxTouch |
| Glass Thickness | 1.1 mm | uxTouch |
| CTP View Area | 155.01 mm x 86.72 mm | uxTouch |
| Sensor Active Area | 156.68 mm x 88.52 mm | uxTouch |
| Structure type | Glass + Glass | uxTouch |
| Surface Hardness | 7H | uxTouch |

### 14.2 Electrical characteristics

| DESCRIPTION | | SPECIFICATION |
| --- | --- | --- |
| Power Consumption (IDD) | Active Mode | 90 mA |
| Power Consumption (IDD) | Sleep Mode | 10 mA |
| Linearity | | +/- 1.5mm |
| Controller | | ILI2132A |
| Resolution | | 1024 x 600 |

---

<!-- p.16 -->

## 15. INSPECTION

Standard acceptance/rejection criteria for TFT module

### 15.1 Inspection condition

Ambient conditions:

- Temperature: 25 ± 2°C
- Humidity: (60 ± 10) %RH
- Illumination: Single fluorescent lamp non-directive (300 to 700 lux)

Viewing distance: 35 ± 5cm between inspector bare eye and LCD.

Viewing Angle: U/D: 45°/45°, L/R: 45°/45°

*Figure (described):* isometric sketch of the LCD lying flat with an inspection cone rising from
its centre. The cone half-angles are marked 45° either side of the surface normal (the normal
itself marked 90° to the panel plane), and the eye position is set 30-40 cm above the panel.

---

<!-- p.17 -->

### 15.2 Inspection standard

*(One ITEM per block below; each ITEM's CRITERION cell in the original is itself a table,
headed by the panel size the criteria apply to.)*

**ITEM: Black spots, white spots, light leakage, Foreign Particle (round Type)**

*Figure (described):* an ellipse with horizontal extent x and vertical extent y, giving
D=(x+y)/2. Spots density: 10 mm.

CRITERION — Size =7"

| Average Diameter | Qualified Qty |
| --- | --- |
| D ≤ 0.2 mm | Ignored |
| 0.2 mm < D ≤ 0.3 mm | N≤3 |
| 0.5mm < D | Not allowed |

**ITEM: LCD black spots, white spots, light leakage (line Type)**

*Figure (described):* a curved line defect with its Length and Width dimensioned. Spots
density: 10 mm.

CRITERION — Size = 7"

| Length | Width | Qualified Qty |
| --- | --- | --- |
| - | W ≤ 0.05 | Ignored |
| L ≤ 5.0 | 0.05< W ≤ 0.1 | N≤3 |
| 5.0 < L | 0.1< W | Not allowed |

**ITEM: Bright/Dark Dots**

CRITERION — Size = 7

| Item | Qualified Qty |
| --- | --- |
| Bright dots | N ≤ 2 |
| Dark dots | N ≤ 3 |
| Total Bright and Dark Dots | N ≤ 4 |

**ITEM: Clear spots**

CRITERION — Size ≥ 5"

| Average Diameter | Qualified Qty |
| --- | --- |
| D < 0.2 mm | Ignored |
| 0.2 mm < D < 0.3 mm | 4 |
| 0.3 mm < D < 0.5 mm | 2 |
| 0.5 mm < D | 0 |

Spots density: 10 mm

**ITEM: Polarizer bubbles**

CRITERION — Size ≥ 5"

| Average Diameter | Qualified Qty |
| --- | --- |
| D < 0.2 mm | Ignored |
| 0.2 mm < D < 0.5 mm | 2 |
| 0.5 mm < D | 1 |

**ITEM: Touch panel spots**

CRITERION — Size ≥ 5"

| Average Diameter | Qualified Qty |
| --- | --- |
| D < 0.25 mm | Ignored |
| 0.25 mm < D < 0.5 mm | 4 |

---

<!-- p.18 -->

*(Continuation of the touch panel spots criterion from p.17.)*

| Average Diameter | Qualified Qty |
| --- | --- |
| 0.5 mm < D | 0 |

**ITEM: Touch panel white line scratch**

CRITERION — Size ≥ 5"

| Length | Width | Qualified Qty |
| --- | --- | --- |
| - | W < 0.03 | Ignored |
| L < 5.0 | 0.03 < W < 0.05 | 2 |
| - | 0.05 < W | 0 |

## 16. RELIABILITY TEST

| NO. | TEST ITEM | TEST CONDITION | NOTE |
| --- | --- | --- | --- |
| 1 | High Temperature Storage | 80°C/120 hours | Note 1 |
| 2 | Low Temperature Storage | -30°C/120 hours | Note 1 |
| 3 | High Temperature Operating | 70 °C /120 hours | Note 1 |
| 4 | Low Temperature Operating | -20°C/120 hours | Note 1 |
| 5 | High Temperature and High Humidity | Humidity 40℃, 90%RH, 120Hrs | Note 1 |
| 6 | Thermal Cycling Test (No operation) | -20℃ for 30min, 70℃ for 30 min.<br>100 cycles. Then test at room temperature after 1 hour | Note 2 |
| 7 | Vibration Test | Frequency: 10 ÷ 55 Hz.<br>Stroke: 1.5 mm.<br>Sweep: 10Hz ÷ 55Hz ÷ 10 Hz.<br>2 hours for each direction of X, Y, Z<br>(Total 6 hours) | |
| 8 | Package Drop Test | Height: 60 cm<br>1 corner, 3 edges, 6 surfaces | |

**Note 1.** Sample quantity for each test item is 5 ÷ 10 pcs.

**Note 2.** Before cosmetic and function test, the product must have enough recovery time, at
least 2 hours at room temperature.

---

<!-- p.19 -->

## 17. LEGAL INFORMATION

Riverdi grants the guarantee for the proper operation of the goods for a period of 12 months
from the date of possession of the goods. If in a consequence of this guaranteed execution the
customer has received the defects-free item as replacement for the defective item, the
effectiveness period of this guarantee shall start anew from the moment the customer receives
the defects-free item.

Information about device is the property of Riverdi and may be the subject of patents pending
or granted. It is not allowed to copy or disclosed this document without prior written
permission.

Riverdi endeavors to ensure that all contained information in this document is correct but does
not accept liability for any error or omission. Riverdi products are in developing process and
published information may be not up to date. Riverdi reserves the right to update and makes
changes to Specifications or written material without prior notice at any time. It is important
to check the current position with Riverdi.

Images and graphics used in this document are only for illustrative the purpose. All images and
graphics are possible to be displayed on the range products of Riverdi, however the quality may
vary. Riverdi is no liable to the buyer or to any third party for any indirect, incidental,
special, consequential, punitive, or exemplary damages (including without limitation lost
profits, lost savings, or loss of business opportunity) relating to any product, service
provided or to be provided by Riverdi, or the use or inability to use the same, even if Riverdi
has been advised of the possibility of such damages.

Riverdi products are not fault tolerant nor designed, manufactured or intended for use or
resale as on line control equipment in hazardous environments requiring fail–safe performance,
such as in the operation of nuclear facilities, aircraft navigation or communication systems,
air traffic control, direct life support machines or weapons systems in which the failure of
the product could lead directly to death, personal injury or severe physical or environmental
damage ('High-Risk Activities'). Riverdi and its suppliers specifically disclaim any expressed
or implied warranty of fitness for High-Risk Activities. Using Riverdi products and devices in
'High-Risk Activities' and in any other application is entirely at the buyer's risk, and the
buyer agrees to defend, indemnify and hold harmless Riverdi from all damages, claims or
expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any
Riverdi intellectual property rights.

*(Riverdi mascot illustration with the speech bubble: "Hi, I am here to help you! If you have
any additional questions, please contact our support via email: contact@riverdi.com")*