Force master/slave roles at bringup (A master / B slave, IEEE 7.32): the AN role lottery plus per-training DSP convergence moves per-pair SNR up to ~3.6 dB, so sessions are pinned to identical conditions; launch power documented firmware-pinned (1.130), single-training SNR documented as a weak qualification number

docs/state.md

@@ -2,7 +2,7 @@
 
 ## Committed tree
 
-AF_PACKET raw sockets everywhere (`sock.go`); flow-director steering; per-packet-MAC-rx-stamped rate buckets (`SO_TIMESTAMPING` cmsg, `rx_filter=ALL` as a hard host check — nics/README.md for what that demands of the NIC; **temporarily bypassed** in `ts.go` so BCM work can run on the X520, which cannot stamp — the check reports yellow and the panel rates read zero there; restore to fatal for the product NIC); read-time-stamped NIC-counter rates; test interfaces pinned to MTU 9000 with a 9018-byte jumbo in the size mix (the modules' jumbo path is exercised, not assumed); BCM module diagnostics (`phy.go`, over the patched-ixgbe `sff_i2c` debugfs, compound-op framing; one per-module lock around every whole operation, and steady-state work time-division-multiplexed with the firmware's own mailbox client — every operation admitted only inside a 3.4 s window after each observed internal temp poll, which ends the stale-read poisoning of the corrected channel — modules/fs/ for the full trap list and validation): bringup identifies both modules and forces EEE off and jumbo on every boot — no trustworthy readback exists and no cable is guaranteed to probe through; the ECD — per-pair verdicts, lengths and pair maps are the length/wiring path — runs through one async path at startup and on every reset, never blocking the UI, with counters re-baselining only after the diag's own link blip so it is never charged to the run; a 1 Hz poller feeds per-pair SNR margin (vs the ≈26.5 dB operating point; green ≥ 3 dB, amber ≥ 1 dB — provisional until the graded-noise run) and the corrected-error set (PCS 3.33 errored blocks/BER, PMA 1.147 fast-retrain count) to the panel and console; framebuffer UI; harness.
+AF_PACKET raw sockets everywhere (`sock.go`); flow-director steering; per-packet-MAC-rx-stamped rate buckets (`SO_TIMESTAMPING` cmsg, `rx_filter=ALL` as a hard host check — nics/README.md for what that demands of the NIC; **temporarily bypassed** in `ts.go` so BCM work can run on the X520, which cannot stamp — the check reports yellow and the panel rates read zero there; restore to fatal for the product NIC); read-time-stamped NIC-counter rates; test interfaces pinned to MTU 9000 with a 9018-byte jumbo in the size mix (the modules' jumbo path is exercised, not assumed); BCM module diagnostics (`phy.go`, over the patched-ixgbe `sff_i2c` debugfs, compound-op framing; one per-module lock around every whole operation, and steady-state work time-division-multiplexed with the firmware's own mailbox client — every operation admitted only inside a 3.4 s window after each observed internal temp poll, which ends the stale-read poisoning of the corrected channel — modules/fs/ for the full trap list and validation): bringup identifies both modules and forces EEE off, jumbo on and the master/slave roles (A master / B slave — left to AN the role is a per-training lottery) every boot — no trustworthy readback exists and no cable is guaranteed to probe through; the ECD — per-pair verdicts, lengths and pair maps are the length/wiring path — runs through one async path at startup and on every reset, never blocking the UI, with counters re-baselining only after the diag's own link blip so it is never charged to the run; a 1 Hz poller feeds per-pair SNR margin (vs the ≈26.5 dB operating point; green ≥ 3 dB, amber ≥ 1 dB — provisional until the graded-noise run) and the corrected-error set (PCS 3.33 errored blocks/BER, PMA 1.147 fast-retrain count) to the panel and console; framebuffer UI; harness.
 
 ## Stashes